很多朋友可能買了超聲波清洗機之后并不知道怎么去操作使用，那接下來就讓小編給大家介紹一下超聲波清洗機正確操作步驟吧。

Many friends may not know how to operate the ultrasonic cleaning machine after buying it. Next, let Xiaobian introduce you to the correct operation steps of the ultrasonic cleaning machine.

安裝超聲波清洗機

Installation of ultrasonic cleaning machine

清洗機電控柜與主機之間的溫控傳感器信號線、超聲波驅動線、加熱器控制線等線路請參考超聲波清洗機安裝手冊，并接好相應的電源。對應的機器，安裝好清洗機的供水管,排水管和溢流排水管松手。

Please refer to the installation manual of ultrasonic cleaning machine for the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the cleaning electromechanical control cabinet and the host, and connect the corresponding power supply. For the corresponding machine, install the water supply pipe, drainage pipe and overflow drainage pipe of the cleaning machine and let go.

加溶質清洗

Solute cleaning

在清洗池中加入適量的清水。液位的高度取決于要清洗的部件。一般不超過清洗池的四分之三。當然，超聲波清洗機的內壁也標明了清洗機的很高水位。只需加水或其他溶劑。說到質量，要注意超聲波清洗機內壁以上的很高水位。

Add an appropriate amount of clean water to the cleaning tank. The height of the liquid level depends on the components to be cleaned. Generally not more than three quarters of the cleaning tank. Of course, the inner wall of the ultrasonic cleaning machine also indicates the high water level of the cleaning machine. Just add water or other solvents. When it comes to quality, pay attention to the high water level above the inner wall of the ultrasonic cleaning machine.

在超聲波清洗機中加入清洗劑

Add cleaning agent to ultrasonic cleaning machine

如果要清洗的物品需要用清洗劑清洗，在加入清洗物品的溶質后，再將清洗劑加入清洗槽中。緩慢攪拌溶質使其充分溶解（同時打開超聲波清洗機的開關，啟動機器攪拌溶劑，清洗代理人）。

If the articles to be cleaned need to be cleaned with cleaning agent, add the cleaning agent into the cleaning tank after adding the solute of the cleaned articles. Slowly stir the solute to fully dissolve it (at the same time, turn on the switch of the ultrasonic cleaning machine, start the machine to stir the solvent and clean the agent).

超聲波清洗機預處理

Pretreatment of ultrasonic cleaning machine

清洗前請用竹刀將零件表面的污垢清理干凈（如果煙塵較多，曲線圖中筒件變化時會出現很多很容易去除的厚泥蓋）進行簡單清洗，以延長清洗液的使用壽命。超聲波可用于精密清洗，但其處理污泥的能力較弱，因此在預處理過程中，應盡可能去除黃泥和泥狀污垢。

Before cleaning, please clean the dirt on the surface of the parts with a bamboo knife (if there is more smoke, there will be many thick mud covers that can be easily removed when the cylinder parts in the curve change) for simple cleaning, so as to prolong the service life of the cleaning solution. Ultrasonic can be used for precision cleaning, but its ability to treat sludge is weak. Therefore, yellow mud and muddy dirt should be removed as much as possible in the pretreatment process.

放入需要清洗的物品

Put in items to be cleaned

將要清洗的物體放入清洗機的清洗藍中，輕輕放入超聲波清洗機的清洗槽中。一次放置的物體較多時，盡量使它們均勻分布在清潔藍中，避免重疊。

Put the object to be cleaned into the cleaning blue of the cleaning machine and gently put it into the cleaning tank of the ultrasonic cleaning machine. When there are many objects placed at one time, try to make them evenly distributed in the clean blue to avoid overlap.

啟動超聲波清洗機

Start the ultrasonic cleaning machine

超聲波清洗機使用非常方便，直接按機器的開關機鍵即可。如果是功率可調的機器，開機后可以選擇自己需要的對應機器頻率。同時，在一些超聲波清洗機的顯示屏上帶有數顯查看相應的頻率和其他數據。

The ultrasonic cleaning machine is very convenient to use. Just press the on / off key of the machine. If it is a machine with adjustable power, you can select the corresponding machine frequency you need after starting up. At the same time, there is a digital display on the display screen of some ultrasonic cleaning machines to view the corresponding frequency and other data.

超聲波清洗機停止

Stop of ultrasonic cleaning machine

如果在超聲波清洗設備清洗過程中要停止清洗，應先將功率調到很小，然后按下停止鍵。清潔時間取決于清潔表面的狀況。

If you want to stop cleaning during the cleaning of ultrasonic cleaning equipment, you should first adjust the power to very small, and then press the stop key. The cleaning time depends on the condition of the cleaned surface.

超聲波清洗器溢出

Ultrasonic washer overflow

如果清洗池的液面上浮油過多，應打開清洗機的溢流裝置將其清除，防止對被清洗物造成二次污染。具體操作如下：打開溢流排放閥，將水或清洗液注入清洗池，直到清洗液開始溢出（建議使用刮刀式器具將浮油向溢流口切割，促使其快速流出），保持溢流排放閥常閉，防止意外溢流造成地面污染。

If there is too much oil floating on the liquid level of the cleaning tank, open the overflow device of the cleaning machine to remove it to prevent secondary pollution to the cleaned objects. The specific operations are as follows: open the overflow discharge valve and inject water or cleaning solution into the cleaning tank until the cleaning solution begins to overflow (it is recommended to use a scraper to cut the floating oil to the overflow port to make it flow out quickly), and keep the overflow discharge valve normally closed to prevent accidental overflow from causing ground pollution.

超聲波清洗機在如今生活的日常商業與工業及更多的作業中應用頗多，但是由于超聲波清洗機也是有許多使用學問的，比如說超聲波清洗機在使用安裝的過程中就存在這很多的步驟，以上便是相關內容了，您想更詳細的了解就來網站www.xingyimei.net咨詢吧。

Ultrasonic cleaning machine is widely used in daily business, industry and more operations in today's life. However, because ultrasonic cleaning machine also has a lot of use knowledge, for example, there are many steps in the process of using and installing ultrasonic cleaning machine. The above is the relevant content. If you want to know more, please come to the website for consultation.