歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

CNC高壓清洗機如何規范使用與日常維護

作者：admin來源：http://www.xingyimei.net/時間：2022-09-06

作為公認的環保、無污染環保設備，CNC高壓清洗機可謂是“美名在外”，不需要更多地夸贊與好處的描述了，所以今天小編不說優勢，只說CNC高壓清洗機如何規范使用與日常維護。

As a recognized environmental protection and pollution-free environmental protection equipment, CNC high-pressure cleaning machine is "famous" and does not need to be praised and described more. Therefore, today's Xiaobian does not talk about advantages, but only how to standardize the use and daily maintenance of CNC high-pressure cleaning machine.

操作說明

Operating instructions

將CNC高壓清洗機放置在一個通風、干燥、無水且無陽光直射暴曬的場所，加以固定。

Place the CNC high-pressure washer in a ventilated, dry, anhydrous place without direct sunlight for fixation.

1、將調壓輪旋松，插上電源插頭。

1. Unscrew the pressure regulating wheel and plug in the power plug.

2、打開噴槍，開動開關按鈕（不同清洗機開關按鈕顏色不同，這里不作說明），按下引水閥桿排除進水管及泵內空氣。

2. Open the spray gun, start the switch button (the color of the switch button of different washers is different, which is not explained here), press the water diversion valve stem to exhaust the air in the water inlet pipe and pump.

3、待噴槍出水后，放開旋動調壓輪，調節輸出壓力至合適程度即可。如果電壓偏低應降低輸出壓力，以減輕電動機負荷，如電壓低于或高于清洗機所能承受的負荷與范圍，需要立刻停止使用，避免燒毀電動機。

3. After the spray gun discharges water, release and rotate the pressure regulating wheel to adjust the output pressure to an appropriate level. If the voltage is low, the output pressure should be reduced to reduce the load of the motor. If the voltage is lower or higher than the load and range that the washer can bear, it is necessary to stop using it immediately to avoid burning the motor.

保養維護方法

Maintenance method

定期檢查電源插頭、電源線、漏電保護裝置，如有損壞，應該立即停止使用，聯系的人士進行維修處理。

Regularly check the power plug, power cord and leakage protection device. In case of damage, stop using immediately and contact professional personnel for maintenance.

定期檢查接地裝置，保證良好接地。

Check the grounding device regularly to ensure good grounding.

電動機、控制裝置如進水、受潮，嚴禁使用并立即維修。

If the motor and control device are affected by water or moisture, it is forbidden to use them and repair them immediately.

定期檢查潤滑油，應保持在油位刻線上，潤滑油每動轉200小時更換一次。如有其它液體進入曲軸箱內應及時換油。

Check the lubricating oil regularly and keep it on the oil level mark. Replace the lubricating oil every 200 hours. If any other liquid enters the crankcase, the oil shall be changed in time.
CNC高壓清洗機

檢查三角皮帶松緊程度，如不合格應及時調整。

Check the tightness of the V-belt and adjust it in time if it is unqualified.

定期檢查各連接、緊固部位螺釘有無松動，如有松動應立即擰緊。

Regularly check whether the screws of all connecting and fastening parts are loose. If they are loose, tighten them immediately.

定期清洗水池、清除濾網上的雜質。

Regularly clean the water tank and remove impurities on the filter screen.

這里注意:維修保養時請切除電源、密封圈裝配前應涂抹黃油再裝上。

Note here: during maintenance, please cut off the power supply. Before assembly, the sealing ring should be coated with grease and then installed.

CNC高壓清洗機如何規范使用與日常維護的相關內容便是如此了，您對此有什么不明白的方面，歡迎來我們網站www.xingyimei.net進行咨詢了解！

This is how to standardize the use and daily maintenance of CNC high-pressure cleaning machines. If you don't understand anything about this, please come to our website www.xingyimei.net for consultation!

上一篇：冬季低溫廢水回收設備運行注意事項
下一篇：碳氫清洗機能使用水基溶劑清洗零部件嗎？