高壓水射流清洗設備憑借其高效、環保的特性，已成為工業清洗領域的重要工具。然而，其強大的水壓也意味著操作不當可能帶來安全隱患或設備損壞。為確保清洗作業的安全與高效，請嚴格遵守以下操作規范。

　　High pressure water jet cleaning equipment has become an important tool in the field of industrial cleaning due to its high efficiency and environmental friendliness. However, its strong water pressure also means that improper operation may pose safety hazards or equipment damage. To ensure the safety and efficiency of cleaning operations, please strictly follow the following operating procedures.

　　安全操作規范

　　Safety operation standards

　　個人防護不可少

　　Personal protection is essential

　　操作時務必穿戴防護眼鏡、防濺手套及防水工作服，避免高壓水射流造成意外傷害。

　　Be sure to wear protective goggles, splash proof gloves, and waterproof work clothes during operation to avoid accidental injuries caused by high-pressure water jets.

　　設備檢查是關鍵

　　Equipment inspection is key

　　啟動前，需全面檢查高壓泵、輸水管路及噴嘴狀態，確保無破損或滲漏，發現問題應及時維修或更換，杜絕隱患。

　　Before starting, it is necessary to conduct a comprehensive inspection of the high-pressure pump, water supply pipeline, and nozzle status to ensure that there is no damage or leakage. If any problems are found, they should be repaired or replaced in a timely manner to eliminate hidden dangers.

　　電源安全須重視

　　Power safety must be taken seriously

　　確保設備電源連接穩固，并做好接地保護，防止漏電風險。

　　Ensure that the device's power connection is stable and properly grounded to prevent the risk of electrical leakage.

　　作業區域要警戒

　　The homework area should be guarded

　　嚴禁將高壓噴嘴朝向人員、設備或其他物體噴射，防止高壓水流沖擊導致傷害或損壞。

　　It is strictly prohibited to spray high-pressure nozzles towards personnel, equipment, or other objects to prevent injury or damage caused by the impact of high-pressure water flow.

　　清洗對象注意事項

　　Precautions for cleaning objects

　　了解材質與污垢特性

　　Understand the characteristics of materials and dirt

　　根據被清洗物的材質（如金屬、塑料等）、結構及污垢類型（油漬、銹跡等），合理調整水壓及噴嘴類型。例如，易損件應采用低壓清洗，頑固污漬可適當提高壓力或搭配專用清洗劑。

　　Adjust the water pressure and nozzle type reasonably according to the material (such as metal, plastic, etc.), structure, and dirt type (oil stains, rust, etc.) of the cleaned object. For example, vulnerable parts should be cleaned with low pressure, and stubborn stains can be treated with increased pressure or special cleaning agents.

　　固定小型部件

　　Fixed small components

　　清洗小型工件時，需使用夾具或固定裝置，避免高壓水流沖擊導致移位或飛濺，影響清洗效果或損壞設備。

　　When cleaning small workpieces, fixtures or fixing devices should be used to avoid displacement or splashing caused by high-pressure water flow impact, which may affect the cleaning effect or damage the equipment.

　　清洗操作要點

　　Key points of cleaning operation

　　壓力與流量調節

　　Pressure and flow regulation

　　初始階段建議采用較低壓力試清洗，隨后根據污垢清除效果逐步調整，避免壓力過高損傷工件或過低影響清潔效率。

　　In the initial stage, it is recommended to use a lower pressure test for cleaning, and then gradually adjust according to the dirt removal effect to avoid damaging the workpiece due to excessive pressure or affecting the cleaning efficiency due to insufficient pressure.

　　噴嘴距離與角度控制

　　Control of nozzle distance and angle

　　噴嘴與清洗面的理想距離為10~30厘米，角度需根據表面形狀靈活調整，確保水流均勻覆蓋并有效剝離污垢。

　　The ideal distance between the nozzle and the cleaning surface is 10-30 centimeters, and the angle needs to be flexibly adjusted according to the surface shape to ensure uniform water flow coverage and effective removal of dirt.

　　勻速移動噴嘴

　　Moving nozzle at a constant speed

　　清洗大面積表面時，采用往復或螺旋式移動路徑，避免局部過度清洗或遺漏。

　　When cleaning large surfaces, use reciprocating or spiral movement paths to avoid excessive cleaning or omission of local areas.

　　遵循合理清洗順序

　　Follow a reasonable cleaning sequence

　　復雜結構或組裝件應遵循“先易后難”原則，優先處理開放區域，再清潔隱蔽部位，防止污垢二次污染。

　　Complex structures or assembled parts should follow the principle of "easy first, difficult later", prioritize handling open areas, and then clean concealed parts to prevent secondary pollution from dirt.

　　清洗后維護措施

　　Maintenance measures after cleaning

　　設備停機與排水

　　Equipment shutdown and drainage

　　作業結束后，先切斷電源，再開啟排水閥排盡余水，防止內部殘留導致銹蝕。

　　After the homework is completed, cut off the power first, and then open the drainage valve to drain the remaining water to prevent internal residue from causing rust.

　　噴嘴與管路維護

　　Nozzle and pipeline maintenance

　　及時清理噴嘴堵塞物，檢查輸水管路是否完好，避免扭曲或壓折。

　　Timely clean the nozzle blockage, check whether the water supply pipeline is intact, and avoid twisting or folding.

　　設備干燥與存放

　　Equipment drying and storage

　　用干布擦拭設備外殼，關鍵金屬部件可涂抹防銹油，并存放在干燥通風處，延長使用壽命。

　　Wipe the equipment casing with a dry cloth, apply anti rust oil to key metal components, and store them in a dry and ventilated place to extend their service life.

　　高壓水射流清洗設備的高效性依賴于規范操作與科學維護。通過嚴格執行上述流程，不僅能提升清洗質量，更能保障人員安全與設備穩定運行，為工業清潔提供可靠支持。

　　The efficiency of high-pressure water jet cleaning equipment depends on standardized operation and scientific maintenance. By strictly following the above process, not only can the cleaning quality be improved, but also the safety of personnel and the stable operation of equipment can be guaranteed, providing reliable support for industrial cleaning.

本文由CNC高壓清洗機友情奉獻.更多有關的知識請點擊:http://www.xingyimei.net我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.xingyimei.net We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message