超聲波清洗機憑借其高效、環保的特性，在精密制造、醫療及珠寶等領域廣泛應用。然而，部分用戶反饋設備清洗效果未達預期，甚至出現污漬殘留現象。這一問題的根源往往涉及設備選型、操作規范及維護保養等多個環節，需從技術原理與實際應用結合的角度進行系統性分析。

　　Ultrasonic cleaning machines are widely used in precision manufacturing, medical, and jewelry fields due to their high efficiency and environmental friendliness. However, some users have reported that the cleaning effect of the equipment did not meet expectations, and even resulted in residual stains. The root cause of this problem often involves multiple aspects such as equipment selection, operation standards, and maintenance, and requires a systematic analysis from the perspective of combining technical principles with practical applications.

　　一、設備選型與工況不匹配

　　1、 Equipment selection does not match working conditions

　　功率密度不足：

　　Insufficient power density:

　　超聲波清洗效能與功率密度直接相關，標準要求槽體底部功率密度不低于0.3W/cm?。若設備功率不足，空化效應強度將衰減40%以上，導致盲孔、微縫等區域清洗盲區擴大。

　　The efficiency of ultrasonic cleaning is directly related to power density, and the standard requires that the power density at the bottom of the tank should not be less than 0.3W/cm?. If the device power is insufficient, the cavitation effect intensity will decrease by more than 40%, leading to the expansion of cleaning blind spots in blind holes, micro cracks and other areas.

　　解決方案：根據工件材質與污垢類型選擇功率密度，重油污工件需選配0.5W/cm?以上機型。

　　Solution: Choose the power density based on the material of the workpiece and the type of dirt, and select 0.5W/cm for heavy oil contaminated workpieces? The above models.

　　頻率選擇偏差：

　　Frequency selection deviation:

　　20-40kHz為通用頻段，但針對不同污垢存在最佳頻率窗口。例如，拋光蠟殘留需25kHz低頻段強化空化沖擊，而指紋油污則需40kHz高頻段提升微射流精度。

　　20-40kHz is a universal frequency band, but there is an optimal frequency window for different types of dirt. For example, polishing wax residue requires 25kHz low-frequency band to enhance cavitation impact, while fingerprint oil stains require 40kHz high-frequency band to improve micro jet accuracy.

　　解決方案：采用雙頻切換機型，根據污垢類型動態調整工作頻率。

　　Solution: Adopting a dual frequency switching model, dynamically adjusting the operating frequency according to the type of dirt.

　　二、清洗工藝參數失控

　　2、 Out of control cleaning process parameters

　　清洗液失效：

　　Cleaning solution failure:

　　堿性清洗液使用超過8小時后，pH值下降導致皂化反應速率降低30%，油污分解能力顯著衰減。

　　After using alkaline cleaning solution for more than 8 hours, the pH value decreases, resulting in a 30% decrease in the saponification reaction rate and a significant decline in the ability to decompose oil stains.

　　解決方案：配置在線pH監測模塊，當pH值低于10時自動補充清洗劑。

　　Solution: Configure an online pH monitoring module to automatically replenish cleaning agents when the pH value is below 10.

　　溫度管理失當：

　　Improper temperature management:

　　水基清洗液最佳工作溫度為50-60℃，溫度每升高10℃，空化效應強度提升15%，但超過70℃會導致清洗液蒸發加劇，空化核數量減少。

　　The optimal working temperature for water-based cleaning solution is 50-60 ℃. For every 10 ℃ increase in temperature, the cavitation effect intensity increases by 15%. However, exceeding 70 ℃ will lead to increased evaporation of the cleaning solution and a decrease in the number of cavitation nuclei.

　　解決方案：采用PTC恒溫加熱系統，溫度波動控制在±2℃以內。

　　Solution: Adopt PTC constant temperature heating system, with temperature fluctuations controlled within ± 2 ℃.

　　時間設定錯誤：

　　Time setting error:

　　實驗數據顯示，鋁合金工件除油清洗需至少15分鐘才能達到98%潔凈度，時間不足將導致碳氫化合物殘留。

　　Experimental data shows that oil removal and cleaning of aluminum alloy workpieces require at least 15 minutes to achieve 98% cleanliness, and insufficient time will result in residual hydrocarbons.

　　解決方案：建立工件材質-污垢類型-清洗時間映射表，通過PLC程序實現精準計時控制。

　　Solution: Establish a mapping table for workpiece material, dirt type, and cleaning time, and achieve precise timing control through PLC program.

　　三、操作規范缺失

　　3、 Lack of operational standards

　　裝載方式不當：

　　Improper loading method:

　　工件疊放導致超聲波衰減系數增加，底部工件接收能量僅為表面工件的40%，形成清洗死角。

　　The stacking of workpieces leads to an increase in ultrasonic attenuation coefficient, and the bottom workpiece receives only 40% of the energy of the surface workpiece, forming a cleaning blind spot.

　　解決方案：采用分層托盤架，工件間距保持10mm以上，確保聲場均勻穿透。

　　Solution: Adopt a layered tray rack with a workpiece spacing of at least 10mm to ensure even penetration of the sound field.

　　預處理缺失：

　　Preprocessing missing:

　　重油污工件直接清洗時，油膜厚度超過0.2mm將形成隔聲層，阻礙超聲波傳導。

　　When cleaning heavy oil contaminated workpieces directly, if the oil film thickness exceeds 0.2mm, a sound insulation layer will be formed, which will hinder the transmission of ultrasonic waves.

　　解決方案：增加溶劑浸泡預處理工序，溶解表面浮油后再進行超聲波清洗。

　　Solution: Add a solvent immersion pretreatment process, dissolve surface floating oil, and then perform ultrasonic cleaning.

　　四、設備維護缺陷

　　4、 Equipment maintenance defects

　　換能器積垢：

　　Scale buildup on the transducer:

　　水垢在換能器振子表面沉積0.5mm后，振幅衰減達20%，空化效應強度顯著降低。

　　After depositing 0.5mm of scale on the surface of the transducer oscillator, the amplitude attenuation reaches 20% and the cavitation effect intensity significantly decreases.

　　解決方案：每月用檸檬酸溶液循環清洗換能器，去除無機鹽沉積。

　　Solution: Clean the transducer with citric acid solution every month to remove inorganic salt deposits.

　　降振系統失效：

　　Vibration reduction system failure:

　　彈性減震墊老化導致槽體共振頻率偏移，聲場分布均勻性下降15%。

　　The aging of the elastic shock absorber pad causes a shift in the resonance frequency of the groove, resulting in a 15% decrease in the uniformity of the sound field distribution.

　　解決方案：每年更換硅膠減震墊，定期檢測槽體固有頻率。

　　Solution: Replace the silicone shock absorber pad annually and regularly check the natural frequency of the groove body.

　　超聲波清洗機清洗效果不佳的本質，是設備性能與工藝需求失配的集中體現。用戶需從選型適配性、工藝參數控制、操作規范性、設備維護四個維度建立標準化作業流程。通過引入在線監測、智能控制等技術手段，可顯著提升清洗質量穩定性，使潔凈度達標率從75%提升至95%以上，真正發揮超聲波清洗技術的效能優勢。

　　The essence of the poor cleaning effect of ultrasonic cleaning machines is the concentrated reflection of the mismatch between equipment performance and process requirements. Users need to establish standardized operating procedures from four dimensions: selection adaptability, process parameter control, operational standardization, and equipment maintenance. By introducing technologies such as online monitoring and intelligent control, the stability of cleaning quality can be significantly improved, and the cleanliness compliance rate can be increased from 75% to over 95%, truly leveraging the efficiency advantages of ultrasonic cleaning technology.

　　本文由超聲波清洗機友情奉獻.更多有關的知識請點擊:http://www.xingyimei.net我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.xingyimei.net We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message